10.54
%
Krytac
ULTIMATE®
Ultimate Upgrade Motor -BOOST- 30K Custom - Short Type
69,90 €*
- CNC machined pinion steel gear- CNC machined stainless steel shaft > - Silicon steel rotor - Precision built motor housing - Heat resistant magnets (Neodym)- Enlarged motor-shaft ball-bearing stabilizers- High-grade silver plated wiring and larger carbon brushes
Nimrod
NT Blackbird 39K CNC Motor Short - Nimrod
64,90 €*
The Blackbird 39K series is built with solid materials and is suitable for nearly every setup. Due to the high rpm, it also can be used in short stroked 0.5 Joules or under 1 Joule builds. Take care of the spring and sector gear management to prevent a pre interlocking which will cause a broken piston or sector gear.
Our magnets can withstand high temperatures up to 150°C
The armature is equipped with a cooling system as well as 0.8mm wires.
The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.
We do recommend using it in the following setups
32:1 / 18:1 / 16:1
Springs: M100 to M140
G&G Armament
Original Motor - short Axis (Short Type) von G&G (18000 RPM)
27,90 €*
NEUWARE OHNE UMVERPACKUNG
Original Motor - short Axis (Short Type) von G&G (18000 RPM)
Der Standard Motor von G&G ist ein hochwertiger Qualitätsmotor und ideal geeignet um defekte oder leistungsschwache Motoren zu ersetzen. Wir empfehlen den Motor für die Verwendung mit Springs bis zu M120
G&G Armament
Motor Mount Set for GR14
20,90 €*
Motor Mount Set for GR14 Material: iron (Eisen)Bitte beachten: Nicht passend für die EBR Serie von G&G. Für diese wird der Art. G-10-089-1 benötigt
ULTIMATE®
Ultimate Upgrade Motor -BOOST- 40K Custom - Long Type
69,90 €*
- CNC machined pinion steel gear- CNC machined stainless steel shaft > - Silicon steel rotor - Precision built motor housing - Heat resistant magnets (Neodym)- Enlarged motor-shaft ball-bearing stabilizers- High-grade silver plated wiring and larger carbon brushes
G&G Armament
Basilisk 17K High Torque Motor Short Type green (17000rpm) - G&G
29,90 €*
Basilisk 17K High Torque Motor Short Type green (17000rpm) - G&G
ARES
Super High Torque Slim Motor und M4 Slim Griff Set schwarz Long axis - Ares
99,90 €*
Super High Torque Slim Motor und M4 Slim Griff Set schwarz Long axis - Ares
Tipp
#OHNE#
Option No.1 Motor Brushless High Torque Motor Long
146,90 €*
The OptionNo.1 brand unveilsa brand new Hi-torque Long Brushless motor that will allow you to upgrade your AEG replica. The special features of the Brushless motor allow you to benefit from impressive performance while reducing electrical consumption and removing the constraints of a conventional carbon motor.
This motor is suitable for all mosfets! * see table below
option-no1-moteur-brushless-hi-torque-lo
- Increased response time compared to a conventional engine
- Power consumption down
- Operation by magnetic field
- No motor brushes
- Heats much less than a conventional engine
- More torque
- No mechanical and electrical loss
- High performance
- Plug-in design simple to install
- 7.4V 31000 rpm LiPo battery
- LiPo 11.1v 46000 rpm battery
- Low voltage protection
- Overheating protection
- 100 Protection temperature protection
Nimrod
NT Blackbird 20K CNC Motor Short - Nimrod
64,90 €*
The Blackbird 20K series is built with solid materials and is suitable for nearly every setup. Due to the high TPA (Turns Per Armature) it can easily pull up all kinds of springs available for AEGs.
Our magnets can withstand high temperatures up to 150°C
The armature is equipped with a cooling system as well as 0.8mm wires.
This motor is perfect for high-speed gears or DSG builts.
The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.
We do recommend using it in the following setups
16:1 /13:1/ 12:1 / DSG
Springs: M120+
3.51
%
G&G Armament
Titan 35K Motor Long Type red (35000rpm) - G&G
54,90 €*
56,90 €*
Titan 35K Motor Long Type red (35000rpm) - G&G
4.62
%
Nimrod
NT Blackbird 39K CNC Motor Long - Nimrod
61,90 €*
64,90 €*
The Blackbird 39K series is built with solid materials and is suitable for nearly every setup. Due to the high rpm, it also can be used in short stroked 0.5 Joules or under 1 Joule builds. Take care of the spring and sector gear management to prevent a pre interlocking which will cause a broken piston or sector gear.
Our magnets can withstand high temperatures up to 150°C
The armature is equipped with a cooling system as well as 0.8mm wires.
The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.
We do recommend using it in the following setups
32:1 / 18:1 / 16:1
Springs: M100 to M140